March 29, 2024, 05:09:35 AM
Forum Rules: Read This Before Posting


Topic: Volumetric flasks and changing volumes  (Read 1640 times)

0 Members and 1 Guest are viewing this topic.

Offline masspecs

  • Regular Member
  • ***
  • Posts: 10
  • Mole Snacks: +0/-0
Volumetric flasks and changing volumes
« on: September 03, 2019, 02:26:00 PM »
I'd like to take a quick survey if I could. For all who routinely create diluted solutions using volumetric flasks, I'm sure you've observed volumes changing sometimes due to chemical interactions (with the meniscus going well above or below). In instances like these, do you prefer to do weight-to-weight dilutions instead of weight-to-volume and volume-to-volume? For example, I created a 20% solution (w/v) of sodium bicarbonate in water. After mixing, the meniscus dwindled well below the line. Should the solution be diluted to the line again in situations like this? Should a weight-to-weight solution be used instead?

Offline Babcock_Hall

  • Chemist
  • Sr. Member
  • *
  • Posts: 5592
  • Mole Snacks: +319/-22
Re: Volumetric flasks and changing volumes
« Reply #1 on: September 03, 2019, 04:08:48 PM »
While we wait for the true analytical chemists to respond, I can say that I was under the impression that the final volume was the critical one.  In other words it is the volume of the solution.  My own opinion is that it is very important to specify exactly what one means when using percentages.  If I mix 70 mL of acetonitrile with 30 mL of water, the final volume is noticeably less than 100 mL.  The way that I understand the definition of a 70% volume to volume aqueous solution of acetonitrile is to take 70 mL of acetonitrile to a final volume of 100 mL with water, regardless of the exact volume of water.

Offline AWK

  • Retired Staff
  • Sr. Member
  • *
  • Posts: 7979
  • Mole Snacks: +555/-93
  • Gender: Male
Re: Volumetric flasks and changing volumes
« Reply #2 on: September 03, 2019, 04:33:43 PM »
Quote
I created a 20% solution (w/v) of sodium bicarbonate in water
Really?
AWK

Offline jeffmoonchop

  • Full Member
  • ****
  • Posts: 334
  • Mole Snacks: +37/-5
  • Gender: Male
Re: Volumetric flasks and changing volumes
« Reply #3 on: September 03, 2019, 04:40:20 PM »
Maybe your solution is undergoing an endothermic or exothermic reaction. With dissolution usually, it's endothermic, as with the mixture of certain solvents, which can cause contraction or expansion of liquids. Perhaps you need to wait until the solution has returned to equilibrium before considering adding more.

Offline Borek

  • Mr. pH
  • Administrator
  • Deity Member
  • *
  • Posts: 27633
  • Mole Snacks: +1799/-410
  • Gender: Male
  • I am known to be occasionally wrong.
    • Chembuddy
Re: Volumetric flasks and changing volumes
« Reply #4 on: September 03, 2019, 06:58:53 PM »
Add enough solvent to make something like 95-99% of the flask volume, mix thoroughly, let it equilibrate the temperature with the surroundings, fill up to mark, mix again. This way final change of the volume will be negligible.
ChemBuddy chemical calculators - stoichiometry, pH, concentration, buffer preparation, titrations.info

Offline Corribus

  • Chemist
  • Sr. Member
  • *
  • Posts: 3471
  • Mole Snacks: +526/-23
  • Gender: Male
  • A lover of spectroscopy and chocolate.
Re: Volumetric flasks and changing volumes
« Reply #5 on: September 04, 2019, 10:16:06 AM »
We do everything gravimetrically.
What men are poets who can speak of Jupiter if he were like a man, but if he is an immense spinning sphere of methane and ammonia must be silent?  - Richard P. Feynman

Offline masspecs

  • Regular Member
  • ***
  • Posts: 10
  • Mole Snacks: +0/-0
Re: Volumetric flasks and changing volumes
« Reply #6 on: September 04, 2019, 01:26:03 PM »
Quote
I created a 20% solution (w/v) of sodium bicarbonate in water
Really?

I misspoke. Sodium carbonate--not bicarbonate.

Offline shchavel

  • Regular Member
  • ***
  • Posts: 46
  • Mole Snacks: +2/-2
Re: Volumetric flasks and changing volumes
« Reply #7 on: September 07, 2019, 11:14:04 AM »
I agree with Borek. It's the right way. In our lab we do the same.

Sponsored Links