March 29, 2024, 12:50:28 AM
Forum Rules: Read This Before Posting


Topic: NaH dispersed in mineral oil (200%)  (Read 2024 times)

0 Members and 1 Guest are viewing this topic.

Offline Malignoalfa

  • Very New Member
  • *
  • Posts: 2
  • Mole Snacks: +0/-0
NaH dispersed in mineral oil (200%)
« on: January 31, 2023, 03:27:22 AM »
synthesizing something I came across the following instruction:

"In a flask at room temperature (20-35 ° C.), 14.1 g (352 mmol) of NaH dispersed in mineral oil (200%) and 200 ml of DMSO were added."

I didn't understand this part:

"NaH dispersed in mineral oil (200%)"

would someone be kind enough to clarify for me?
thanks

Offline Hunter2

  • Sr. Member
  • *****
  • Posts: 2153
  • Mole Snacks: +162/-47
  • Gender: Male
  • Vena Lausa moris pax drux bis totis

Offline Babcock_Hall

  • Chemist
  • Sr. Member
  • *
  • Posts: 5592
  • Mole Snacks: +319/-22
Re: NaH dispersed in mineral oil (200%)
« Reply #2 on: January 31, 2023, 08:54:19 AM »
https://pubs.acs.org/doi/10.1021/ba-1957-0019.ch011
I can only give you a partial answer.  NaH is sold in several forms, including as a dispersion in mineral oil that is 60% NaH by mass (it is safer to handle than dry NaH).  I have only used it one time.  When I did, I weighed out the appropriate mass and rinsed with pentane or petroleum ether to remove the oil, then I used it immediately.  One has to adjust the mass weighed out based on the portion that is mineral oil.  I do not understand the meaning of 200%.
EDT
I am concerned that NaH and DMSO together might constitute a hazard (see link below).  Perhaps there is a different protocol that you could use.
https://pubs.acs.org/doi/10.1021/acs.oprd.9b00276
« Last Edit: January 31, 2023, 09:11:25 AM by Babcock_Hall »

Offline Malignoalfa

  • Very New Member
  • *
  • Posts: 2
  • Mole Snacks: +0/-0
Re: NaH dispersed in mineral oil (200%)
« Reply #3 on: January 31, 2023, 10:50:26 AM »
Thanks for the reply. I'm sure mineral oil is just a safety product for NaH to stop being explosive. That is, it doesn't matter the amount of oil in the reaction, just add the correct mole amount of NaH. I think the 200% refers to 2 parts NaH to one part Oil.
Thanks.

Offline phth

  • Chemist
  • Full Member
  • *
  • Posts: 528
  • Mole Snacks: +39/-4
Re: NaH dispersed in mineral oil (200%)
« Reply #4 on: February 19, 2023, 01:23:08 AM »
Thanks for the reply. I'm sure mineral oil is just a safety product for NaH to stop being explosive. That is, it doesn't matter the amount of oil in the reaction, just add the correct mole amount of NaH. I think the 200% refers to 2 parts NaH to one part Oil.
Thanks.
Could it be 20% dispersion in oil TYPO???? Why not just titrate the base following an established procedure if the protocol does not work???

Offline rolnor

  • Chemist
  • Sr. Member
  • *
  • Posts: 2205
  • Mole Snacks: +149/-10
Re: NaH dispersed in mineral oil (200%)
« Reply #5 on: February 19, 2023, 01:18:41 PM »
200% is not correct in any posssible way. Stupid or typo.

Offline Enthalpy

  • Chemist
  • Sr. Member
  • *
  • Posts: 4041
  • Mole Snacks: +304/-59
Re: NaH dispersed in mineral oil (200%)
« Reply #6 on: February 21, 2023, 06:39:13 PM »
Apologies for interrupting...

Experiments in 2019 have shown a degree of danger previously unknown from NaH in several solvents, especially DMSO. The sensitivity and the force of the explosion weren't suspected. Impressive pictures with less than 14g, rather 0.5g NaH.
  pubs.acs.org - science.org

Older papers ignore it hence don't mention it. So be cautious.

I'm completely away from anything I believe to understand here, so I can be utterly wrong.

Offline Babcock_Hall

  • Chemist
  • Sr. Member
  • *
  • Posts: 5592
  • Mole Snacks: +319/-22
Re: NaH dispersed in mineral oil (200%)
« Reply #7 on: February 27, 2023, 11:22:58 AM »
"The hazards associated with the thermal decomposition of chemically incompatible sodium hydride solvent matrices are known, with reports from the 1960s detailing the inherent instability of NaH/dimethyl sulfoxide, NaH/N,N-dimethylformamide, and NaH/N,N-dimethylacetamide mixtures."

"The dangers associated with NaH/DMSO mixtures were evidenced by an explosion during the ARC analysis that was forceful enough to displace the ARC housing."

Enthalpy,

I mentioned this problem in an earlier comment, and I am glad that you are highlighting it.

Offline rolnor

  • Chemist
  • Sr. Member
  • *
  • Posts: 2205
  • Mole Snacks: +149/-10
Re: NaH dispersed in mineral oil (200%)
« Reply #8 on: March 11, 2023, 03:31:58 PM »
Thats scary, I have used g-quantities of NaH in DMSO and DMF, even heated it with a heating-gun...  Whats the mechanism, is it red-ox or nucleophilic attack somehow? Free radical?

Sponsored Links