March 28, 2024, 07:34:44 AM
Forum Rules: Read This Before Posting


Topic: Problem in Phase Equilibrium!  (Read 16142 times)

0 Members and 1 Guest are viewing this topic.

Offline Winga

  • Chemist
  • Full Member
  • *
  • Posts: 510
  • Mole Snacks: +39/-10
Problem in Phase Equilibrium!
« on: July 10, 2004, 01:56:03 PM »
Hi Everybody!

Could anyone explain why we use 2 times of 50mL of a solvent for extraction is better than that of using 1 time of 100mL.
 
Thank You!

Offline Donaldson Tan

  • Editor, New Asia Republic
  • Retired Staff
  • Sr. Member
  • *
  • Posts: 3177
  • Mole Snacks: +261/-13
  • Gender: Male
    • New Asia Republic
Re:Problem in Phase Equilibrium!
« Reply #1 on: July 11, 2004, 12:25:40 PM »
do your mathematics
"Say you're in a [chemical] plant and there's a snake on the floor. What are you going to do? Call a consultant? Get a meeting together to talk about which color is the snake? Employees should do one thing: walk over there and you step on the friggin� snake." - Jean-Pierre Garnier, CEO of Glaxosmithkline, June 2006

Offline Winga

  • Chemist
  • Full Member
  • *
  • Posts: 510
  • Mole Snacks: +39/-10
Re:Problem in Phase Equilibrium!
« Reply #2 on: July 11, 2004, 09:50:51 PM »
Sorry, I need an explanation without using any calculation.
(e.g. about the volume & of the solvent, concentration...)

Offline Mitch

  • General Chemist
  • Administrator
  • Sr. Member
  • *
  • Posts: 5298
  • Mole Snacks: +376/-3
  • Gender: Male
  • "I bring you peace." -Mr. Burns
    • Chemistry Blog
Re:Problem in Phase Equilibrium!
« Reply #3 on: July 12, 2004, 07:31:41 PM »
Lets say that your solute is completely soluble in 5 ml of ether. Then why use 2 x 50ml or 1 x 100ml of ether to extract it? Because the extraction procedures are not 100% efficient. Assuming the extraction protocol is 90% efficient then if you do it twice you can get 90% of 90% of the solute out. If you only do it once then you only get 90% of it out. The amout of ether is irrelevant, its a matter of efficiency.
Most Common Suggestions I Make on the Forums.
1. Start by writing a balanced chemical equation.
2. Don't confuse thermodynamic stability with chemical reactivity.
3. Forum Supports LaTex

Offline Winga

  • Chemist
  • Full Member
  • *
  • Posts: 510
  • Mole Snacks: +39/-10
Re:Problem in Phase Equilibrium!
« Reply #4 on: July 12, 2004, 11:46:38 PM »
A further question:
As you say the solute is completely soluble in 5 ml of ether, but if we use 2 ml of ether to do 25 times of extraction, will it affect the original efficiency? (0.9^25)

Offline Mitch

  • General Chemist
  • Administrator
  • Sr. Member
  • *
  • Posts: 5298
  • Mole Snacks: +376/-3
  • Gender: Male
  • "I bring you peace." -Mr. Burns
    • Chemistry Blog
Re:Problem in Phase Equilibrium!
« Reply #5 on: July 12, 2004, 11:49:58 PM »
of course. The efficiency I speak of assumes your using an amount of ether greater than the amount needed for it to be soluble. The correct chemical name for this behavior isn't efficiency, but something else. I'll try to look it up for you tonight when I get home.
Most Common Suggestions I Make on the Forums.
1. Start by writing a balanced chemical equation.
2. Don't confuse thermodynamic stability with chemical reactivity.
3. Forum Supports LaTex

Offline Winga

  • Chemist
  • Full Member
  • *
  • Posts: 510
  • Mole Snacks: +39/-10
Re:Problem in Phase Equilibrium!
« Reply #6 on: July 13, 2004, 12:07:31 AM »
Sorry, my question is that if we use the amount of solvent which cannot completely dissolve the solute in normal condition, (e.g. 5 ml of ether can completely dissolve 1 g of solute), but I just use 2 ml of ether for each extraction, will the efficiency of each extraction lower than 90%?

Thanks a lot! ;)

Offline Mitch

  • General Chemist
  • Administrator
  • Sr. Member
  • *
  • Posts: 5298
  • Mole Snacks: +376/-3
  • Gender: Male
  • "I bring you peace." -Mr. Burns
    • Chemistry Blog
Re:Problem in Phase Equilibrium!
« Reply #7 on: July 13, 2004, 01:20:06 PM »
Yes.

and I looked up the theory. It's not called efficiency but percent recovery..
Most Common Suggestions I Make on the Forums.
1. Start by writing a balanced chemical equation.
2. Don't confuse thermodynamic stability with chemical reactivity.
3. Forum Supports LaTex

Offline Winga

  • Chemist
  • Full Member
  • *
  • Posts: 510
  • Mole Snacks: +39/-10
Re:Problem in Phase Equilibrium!
« Reply #8 on: July 14, 2004, 12:03:57 AM »
Sorry, my question is that if we use the amount of solvent which cannot completely dissolve the solute in normal condition, (e.g. 5 ml of ether can completely dissolve 1 g of solute), but I just use 2 ml of ether for each extraction, will the efficiency of each extraction lower than 90%?
But by this equation,

K = [Solvent A]solute / [Solvent B]solute

If the efficiency / percent recovery of each extraction is lower than the original value, will K still constant?

Sponsored Links